2018 North Carolina Hazardous Waste Compliance Workshop #2 - Greensboro, NC

THE 2018 HAZARDOUS WASTE WORKSHOPS Join us for the 26th Annual NORTH CAROLINA HAZARDOUS WASTE COMPLIANCE WORKSHOP CO-sponsored by the NORTH CAROLINA MANUFACTURERS ALLIANCE (NCMA) and the NORTH CAROLINA DIVISION OF WASTE MANAGEMENT (DWM).  WORKSHOP #2 will be held in GREENSBORO, NC ON THURSDAY, MAY 10, 2018. ------------------------- ADDITIONAL WORKSHOPS The 2018 NC Hazardous Waste Workshops will also be offered on the following dates and locations: MAY 3, 2018 WORKSHOP #1 - WILMINGTON COASTLINE CONVENTION AND EVENT CENTER Click here to register for the May 3, 2018 Workshop [https://hazwaste-compliance-workshop-1-wilmington.eventbrite.com] MAY 17 2018 WORKSHOP #3 - RALEIGH MCKIMMON CENTER Click here to register for the May 17, 2018 Workshop [https://hazwaste-compliance-workshop-3-raleigh.eventbrite.com] MAY 31, 2018 WORKSHOP #4 - ASHEVILLE-HOLIDAY INN ASHEVILLE – BILTMORE WEST Click here to register for the May 31, 2018 Workshop [https://hazwaste-compliance-workshop-4-asheville.eventbrite.com] NOVEMBER 1, 2018 WORKSHOP #5 - CONCORD -THE SPEEDWAY CLUB AT CHARLOTTE MOTOR SPEEDWAY Registration for the November 1, 2018 will open August 31, 2018 ------------------------- ABOUT THIS WORKSHOP Generators of hazardous waste are required to train their employees involved with hazardous waste management. The regulations require facility personnel to complete classroom or on-the-job training to become familiar with proper hazardous waste management and emergency procedures for the wastes handled at the facility. In addition facility personnel must take part in an annual review of their initial training. Now you can learn first-hand what the regulators from the North Carolina Division of Waste Management expect from hazardous waste generators and treatment, storage and disposal facilities. The Workshop is designed for facility personnel with hazardous waste duties ranging from facility environmental coordinators to on-site hazardous waste handlers. Attendees will go through a full-scale inspection presented by the hazardous waste field staff. You will learn what inspectors look for at your facility. Hazardous waste regulations will be discussed focusing on interpretation of these regulations as they apply to your business. Waste minimization and enforcement will be reviewed. There will be plenty of time for questions during each presentation as well as during breaks and lunch. Attendees with specific questions prior to the workshop can also submit those questions to NCMA. NCMA will then provide the questions to DWM staff anonymously so that they can address the questions during the Workshop. ------------------------- AGENDA 7:30 AM - Registration 8:00 AM - Introductions 8:15 AM - New & Proposed Rules 8:45 AM - BREAK 8:55 AM - WASTE IDENTIFICATION PART 1 10:00 AM - BREAK 10:10 AM - WASTE IDENTIFICATION PART 2 11:10 AM - BREAK 11:20 AM - Enforcement 12:00 PM - LUNCH 1:00 PM - WASTE MINIMIZATION 1:30 PM - BREAK 1:40 PM - UNIVERAL WASTE / USED OIL / E-WASTE 2:20 PM - BREAK 2:30 PM - Inspection - Paperwork 3:30 PM - BREAK 3:40 PM - Inspection - Walkthrough ------------------------- LUNCH AND MATERIAL The registration fee includes a Workshop Manual containing copies of all presentations and supporting material. A hot buffet lunch and refreshments during the breaks are also included. ------------------------- COST Standard Registration - $225 NCMA Member Registration - $190 Late Registration (After April 20, 2017) - $275 ------------------------- PRESENTERS The Workshop will be presented by the staff of the Hazardous Waste Section of the North Carolina Division of Waste Management. Presenters include: Brent Burch, Mark Burnette, Heather Goldman, Jenny Patterson, Andrew Martin, Don Burke, Jeff Menzel, Richard Concepción Ernest Lawrence, Jack Kitchen and other regional representatives. ------------------------- ADDITIONAL INFORMATION For Additional Information Contact: Donna Pittman at donna.pittman@myncma.org or 919-834-9459 -------------------------